Stay informed about the latest developments in cabinet manufacturing, IP rating standards, outdoor enclosure technology, and industrial cabinet solutions.
ADB said it will be one of the first utility-scale renewable energy projects with a battery energy storage system (BESS) component in Uzbekistan. It follows the announcement of the county’s first BESS in May 2024 and the connection of the first phase of a 511 MW solar project in March of this year.
Separately, ACWA Power recently announced financial close on a 200 MW solar plant and 500 MWh BESS near the national capital, Tashkent. Uzbekistan had 253 MW of cumulative installed solar capacity at the end of last year, according to figures from the International Renewable Energy Agency (IRENA).
The ADB is proposing a large scale, solar-plus-battery system in Uzbekistan. According to a listing on ADB’s website, the Samarkand 1 Solar PV and BESS Project will involve the construction of two solar power plants, of 100 MW and 400 MW, a pooling station, 500 MWh BESS, loop-in loop-out transmission lines, and a 70 km overhead transmission line.
ACWA Power plans to build a 500 MW solar plant and a 500 MWh battery energy storage system in Uzbekistan under a project proposed by the Asian Development Bank (ADB). The ADB is proposing a large scale, solar-plus-battery system in Uzbekistan.
According to price analysis firm InfoLink: “Since March, the spot price of n-type modules in China has soared from RMB0.7/W to RMB0.73/W. Quotes from leading manufacturers are approaching the RMB0.75/W mark.” The results of the China Datang Group’s 2025-2026 PV module framework. Image: Datang.
On 11 March 2025, the results of the China Datang Group’s 2025-2026 PV module framework purchase tender were announced, with the spot price of n-type modules increasing from RMB0.7/W (US$0.097/W) to RMB0.73/W (US$0.1/W), and some modules priced as high as RMB0.75/W (US$0.11/W).
In May 2025, shifting market dynamics saw solar module prices continue to rise, with supply constraints and firm demand putting upward pressure on pricing. In contrast, inverters trended lower, highlighting diverging developments across the PV value chain.
U.S.: The spot price for TOPCon ≥600wp modules DDP US rose 0.38% this week to $0.264/wp, on a limited number of price reports, with quotes for cargoes from Southeast Asia rising 0.39% to $0.257/wp and quotes for cargoes from India stable week-over-week at $0.288/wp.
Unfortunately, glass-glass PV modules are, similar to regular PV modules, subject to early life failures. A failure of growing concern are defects in the glass layer (s) of PV modules. The scale of decommissioned PV modules with glass defects will increase with the development of solar PV energy [ 7 ].
While there are no technical disadvantages to glass-glass PV modules [ 10, 19 ], in general glass-glass PV designs are more expensive than regular GBS modules due to the use of an additional costly glass layer and the increased weight that may lead to higher costs for support structures.
Glass defects impact the economic performance of a PV system in multiple ways. The most obvious effect is the potential (in)direct performance loss of PV modules, which results in reduced economic revenues. Secondly, PV modules that suffer from glass defects may no longer meet safety requirements, therefore these modules are replaced.
However, glass defects do not directly imply that PV modules endure internal damage nor that PV modules cannot continue to operate with minimal microcracks. Thus far, glass defects have been regarded as a failure beyond repair and no noticeable attempt has been made to develop reparation methods.
Thin-film solar modules transform the renewable energy landscape with their lightweight design, flexibility, and cost-effective production. Unlike traditional silicon-based photovoltaics, thin-film technology enables solar energy harvesting on unconventional surfaces, from building facades to wearable electronics.
The most commonly used ones for thin-film solar technology are cadmium telluride (CdTe), copper indium gallium selenide (CIGS), amorphous silicon (a-Si), and gallium arsenide (GaAs). The efficiency, weight, and other aspects may vary between materials, but the generation process is the same.
Thin film solar cells are favorable because of their minimum material usage and rising efficiencies. The three major thin film solar cell technologies include amorphous silicon (α-Si), copper indium gallium selenide (CIGS), and cadmium telluride (CdTe).
Front. Energy Res., 15 June 2025 Thin-film photovoltaics, particularly those based on perovskite materials, are revolutionizing solar energy research through rapid efficiency gains, innovative device architectures, and advanced modeling techniques.
